MODEL 3131

HEAVY DUTY MANURE SPREADER
MODEL 3131 – 231 BUSHEL

  • A massive unitized welded frame with heavy floor supports and side stakes, wrap around steel front corners. Strong rear main beater side panels are slanted for clearance and wider spread, and then welded to the strong 5″ U channel side members compare with any on the market.
  • The side flares on all H&S “Heavy Duty” manure spreaders are made of 10 gauge g210 culvert grade galvanized steel.
  • Sides, front panel and both sides of the rear hydraulic end gate use fiberglass reinforced plywood to provide for easy cleaning and minimal freeze up. It also features a solid virgin grade poly floor. Considerably less torque is needed to move a heavy load.
  • A front splash guard is standard equipment.
  • Greaseable bearings.
  • The two-speed apron drive is standard equipment. An optional variable speed hydraulic drive is also available. As is an optional electric control for the hydraulic drive.
  • A 29″ diameter beater with 14 replaceable beater paddles. The beater has two types of paddles, blunt for widespread and sharp ripper type for cutting and shredding. The beater side wiper blades are also standard equipment.
  • The hydraulic endgate features 2 cylinders as standard (optional on the 3131). The hydraulic lines are run through a 3×3 tube under the floor. The upright position of the hydraulic cylinder stroke allows the gate to lift with the least strain at pivot points.
  • H&S uses cast special steel alloy apron idler slides instead of idler sprockets making for years of dependable service.
  • Adjustment for the main apron is easy by simply loosening the two side bolts and drawing up the long bolt.
  • Gear box mechanisms and drive for the beater and apron are Timken tapered roller bearing equipped. The beater drive gear box is 1-½″ bevel gear oil bath equipped with a 4-jaw over running clutch for beater shut off. The apron drive is a 50:1 bronze worm gear with shear bolt protection.
  • The strong oil bath bevel gear box that powers the beater is tapered Timken roller bearing equipped. The gear box utilizes a 4-jaw beater shut off clutch and tractor sized spline shaft.
  • Unloading Speed for 3131, 3137, 3143, and W3143 – (2 speed chain drive) High Speed: PTO speed 540 rpm’s 8′8.5″ per minute Low Speed: PTO speed 540 rpm’s 4′8.5″ per minute.
  • An optional top beater is available to provide load leveling and spreading of high heaped loads. (Standard in models 3143 & W3143)
  • The W3143 (western) has all the same features as above with additional features such as double main frame channels, additional floor supports, 1045 hardened drive shaft, #80 drive chain and a heavy duty main gear box.
3123
CAPACITY – OLD RATING 235 B.U.
CAPACITY CU. FT. STRUCK LEVEL 143
TOP OF FLARE WIDTH 68″ (173 CM)
INSIDE WIDTH 60″ (152 CM)
INSIDE LENGTH 12′ 1″ (3.7 M)
INSIDE DEPTH 28 ⅜″ (72 CM)
OVERALL WIDTH W/STANDARD TIRES 94 ½″ (240 CM)
OVERALL LENGTH 18′ 6″ (5.7 M)
OVERALL LOADING HEIGHT-TOP OF FLARE 51.5″ (131 CM)
OVERALL HEIGHT W/HYD. ENDGATE 55″ (140 CM)
DIAMETER OF BEATER 29″ (74 CM)
MAIN APRON CHAIN T-ROD
UPPER BEATER OPTIONAL
SPINDLE SIZE 2″ (5 CM)
STANDARD TIRE SIZE 295×22.5 RECAP
WEIGHT W/TIRES 2890# (1,311 KG)
REAR HYDRAULIC ENDGATE STANDARD
SEMI LIQUID REAR PAN OPTIONAL
PTO SPEED 540
JACK STARDARD
DRIVE 2 SPEED
VARIABLE SPEED HYD. DRIVE OPTIONAL
FRONT SPLASH PANEL STANDARD
HYD. CYL ON HYD. ENDGATE 1-STANDARD 2ND OPTIONAL
3127
CAPACITY – OLD RATING 270 B.U.
CAPACITY CU. FT. STRUCK LEVEL 167
TOP OF FLARE WIDTH 68″ (173 CM)
INSIDE WIDTH 60″ (152 CM)
INSIDE LENGTH 14′ 1″ (4.3 M)
INSIDE DEPTH 28 ⅜″ (72 CM)
OVERALL WIDTH W/STANDARD TIRES 94 ½″ (240 CM)
OVERALL LENGTH 20′ 5.5″ (6.3 M)
OVERALL LOADING HEIGHT-TOP OF FLARE 51.5″ (131 CM)
OVERALL HEIGHT W/HYD. ENDGATE 55″ (140 CM)
DIAMETER OF BEATER 29″ (74 CM)
MAIN APRON CHAIN T-ROD
UPPER BEATER OPTIONAL
SPINDLE SIZE 2 ½″ (6 CM)
STANDARD TIRE SIZE 295×22.5 RECAP
WEIGHT W/TIRES 3230# (1,495 KG)
REAR HYDRAULIC ENDGATE STANDARD
SEMI LIQUID REAR PAN OPTIONAL
PTO SPEED 540
JACK STARDARD
DRIVE 2 SPEED
VARIABLE SPEED HYD. DRIVE OPTIONAL
FRONT SPLASH PANEL STANDARD
HYD. CYL ON HYD. ENDGATE 1-STANDARD 2ND OPTIONAL
3131
CAPACITY – OLD RATING 310 B.U.
CAPACITY CU. FT. STRUCK LEVEL 185
TOP OF FLARE WIDTH 68″ (173 CM)
INSIDE WIDTH 60″ (152 CM)
INSIDE LENGTH 15′ 7″ (4.8 M)
INSIDE DEPTH 28 ⅜″ (72 CM)
OVERALL WIDTH W/STANDARD TIRES 98″ (249 CM)
OVERALL LENGTH 21′ 11.5″ (6.7 M)
OVERALL LOADING HEIGHT-TOP OF FLARE 51.5″ (131 CM)
OVERALL HEIGHT W/HYD. ENDGATE 55″ (140 CM)
DIAMETER OF BEATER 29″ (74 CM)
MAIN APRON CHAIN T-ROD
UPPER BEATER OPTIONAL
SPINDLE SIZE 2 ¼″ (6 CM)
STANDARD TIRE SIZE 295×22.5 RECAP
WEIGHT W/TIRES 4190# (1,901 KG)
REAR HYDRAULIC ENDGATE STANDARD
SEMI LIQUID REAR PAN OPTIONAL
PTO SPEED 540 STANDARD 1000 OPTIONAL
JACK STARDARD
DRIVE 2 SPEED
VARIABLE SPEED HYD. DRIVE OPTIONAL
FRONT SPLASH PANEL STANDARD
HYD. CYL ON HYD. ENDGATE 1-STANDARD 2ND OPTIONAL

WARRANTY: SEE OERATORS MANUAL FOR WARRANTY DETAILS AND LIMITATIONS. H&S RESERVES THE RIGHT TO CHANGE ITS PRODUCTS OR THE DESCRIPTION AT ANY TIME WITHOUT NOTICE OR OBLIGATION. MODELS AND SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE.

A variable speed hydraulic drive is also available on 3123, 3127, 3131, 3137, 3143, and W3143.

Top beater to provide load leveling and spreading of high heaped loads is available on 3123, 3127, 3131, and 3137.

A rear pan is optional on all models.

A semi-liquid hydraulic end gate is standard equipment on all models. An optional second hydraulic end gate cylinder is available for the 3123, 3127, and 3131. The hydraulic lines are run through a 3×3 tube under the floor. The upright position of the hydraulic cylinder stroke allows the gate to lift with the least strain at pivot points.

There was clearly a definite simply click within the keyless functions whenever environment time, and patek philippe replica the date quickset was very irratic, the two typical troubles in order to Seiko 62xx calibres while don begins to placed in.